Communication Modules
Showing all 7 results
-
Bluetooth, Communication Modules
HC-05 Bluetooth Module
The HC-05 is a very cool module which can add two-way (full-duplex) wireless functionality to your projects. You can use this module to communicate between two microcontrollers like Arduino or communicate with any device with Bluetooth functionality like a Phone or Laptop. There are many android applications that are already available which makes this process a lot easier. The module communicates with the help of USART at 9600 baud rate hence it is easy to interface with any microcontroller that supports USART. We can also configure the default values of the module by using the command mode. So if you looking for a Wireless module that could transfer data from your computer or mobile phone to microcontroller or vice versa then this module might be the right choice for you.
SKU: n/a -
Bluetooth, Communication Modules
HC-06 Bluetooth Module
HC-06 is a Bluetooth module designed for establishing short range wireless data communication between two microcontrollers or systems. The module works on Bluetooth 2.0 communication protocol and it can only act as a slave device. This is cheapest method for wireless data transmission and more flexible compared to other methods.
SKU: n/a -
Communication Modules, RFID
RFID Card 13.56 KHz
- Contactless transmission of data and supply energy (no battery needed)
- Operating distance: Up to 100mm (depending on antenna geometry)
- Operating frequency: 13.56MHz
- Data transfer: 106 kbit/s
- Data integrity: 16 Bit CRC,parity,bit coding bit counting
- Anticollision
- Typical tickting transaction: <100 ms ( including backup management)
SKU: n/a -
Communication Modules, RF Modules
Telemetry 3DR TTL
The Radio telemetry system base on 3DR Radio system and 100% compatible.
It’s designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. Its available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground).
The system provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open source firmware. Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.
Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.
SKU: WRE186 -
Communication Modules, XBee
XBee 2mW PCB Antenna – Series 2 (ZigBee Mesh)
This is the XBee XB24-Z7CIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
This Xbee also has a chip antenna which is basically a small chip that acts as an antenna. Quick, easy, cheap, and not in the way.SKU: n/a -
Communication Modules, XBee
XBee 2mW Wire Antenna – Series 2 (ZB)
This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
SKU: WRE676
