Arduino & IOT Boards
Showing 265–285 of 285 results
-
Breakout Boards
USB Type-B Connector Breakout Board
- Effective this breakout board has a USB Type B female connector, with all 4 pins broken out to a DIP 2.54mm header.
- Great for pairing with a microcontroller with USB support, or adding USB 5V power to a project.
- USB 2.0 Type B Female
- 2.54mm Pitch
- DIP4
- color: green
- Material: plastic
- size:20*20*1mm
- Package Contents:
- 2 * USB to DIP adapter board
- Only the above package content, other products are not included.
SKU: n/a -
-
Others, Sensors
Vibration Sensor SW-420
- Dimensions: 40 x 15 x 7 mm(LxWxH).
- Weight: 3 gm.
- Using SW-420 normally closed type vibration sensor
- Comparator output, clean signal, good waveform, strong driving ability, >15mA
- Operating voltage 3.3V ~ 5V
- Output format: digital switching output (0 and 1)
- Using a wide voltage LM393 comparator
- With bolt holes for easy installation
SKU: n/a -
Mic/Voice Recognition
Voice Recognition Module
- Voltage: 4.5-5.5V
- Current: <40mA
- Digital Interface: 5V TTL level for UART interface and GPIO
- Analog Interface: 3.5mm mono-channel microphone connector
and microphone pin interface - Size: 31mm x 50mm
- Recognition accuracy: 99% (under ideal environment)
SKU: n/a -
Arduino & IOT Boards, Module, Shields
W5100 Ethernet Shield
- Operating voltage 5V (supplied from the Arduino Board)
- Ethernet Controller: W5100 with internal 16K buffer
- Connection speed: 10/100Mb
- Connection with Arduino on SPI port
- The Shield contains a number of informational LEDs
- PWR: indicates that the board and shield are powered
- LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
- FULLD: indicates that the network connection is full duplex
- 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
- RX: flashes when the shield receives data
- TX: flashes when the shield sends data
- TX: flashes when the shield sends data
- COLL: flashes when network collisions are detected
SKU: n/a -
Arduino & IOT Boards, Communication Modules, Module, Wifi & Ethernet
W5500 Ethernet Network Module / Shield
Arduino & IOT Boards, Communication Modules, Module, Wifi & EthernetW5500 Ethernet Network Module / Shield
- Operating voltage: 2.97-3.63V
- Current draw: Typical: 128mA, Max: 200mA
- SPI clock frequency: Max: 80MHz
- Ethernet MAC: 10/100BASE-T
- PHY: 10BASE-T and 100BASE-T
- TCP/IP stack: TCP, UDP, IPv4, ICMP, ARP, IGMP, and PPPoE
- Hardware sockets: 8
- Internal buffer: 32KB
- Supports: SPI, WOL, and power down mode
SKU: n/a -
-
Pumps, Sensors, Water, Water Pumps
Waterflow Sensor YFS101
This water flow sensor has a pinwheel sensor inside it which helps the sensor detect how much liquid has passed through it. By counting pulses from the output of the sensor water flow can be calculated. Each pulse is approximately 2.25 millimeters.
SKU: n/a -
Pumps, Sensors, Water, Water Pumps
Waterflow Sensor YFS201
- Model: YF-S201
- Sensor Type: Hall effect
- Working Voltage: 5 to 18V DC (min tested working voltage 4.5V)
- Max current draw: 15mA @ 5V
- Output Type: 5V TTL
- Working Flow Rate: 1 to 30 Liters/Minute
- Working Temperature range: -25 to +80℃
- Working Humidity Range: 35%-80% RH
- Accuracy: ±10%
- Maximum water pressure: 2.0 MPa
- Output duty cycle: 50% +-10%
- Output rise time: 0.04us
- Output fall time: 0.18us
- Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min)
- Pulses per Liter: 450
- Durability: minimum 300,000 cycles
- Cable length: 15cm
- 1/2″ nominal pipe connections, 0.78″ outer diameter, 1/2″ of thread
- Size: 2.5″ x 1.4″ x 1.4″
SKU: n/a -
Buzzers
White Piezo Buzzer
- Its color is White.
- Alarms diameter is 29mm / 1.14”
- Electronic buzzer height is 15mm / 0.59”
- It has 2 mounting holes. And the distance of the holes is 40mm / 1.57”
- Its rated voltages are 12Volts.
- Its operating voltages are 3 to 24 voltages.
- Its rated current is 20mA.
- Its min sound output at 10cm is 95 Db.
- Its resonant frequency is 3100 to +- 500.
- Its operating temperature is -20 to -80 degrees centigrade.
- It has intermittent sound and mounting holes.
- It has good storage and it allows you to use it for a long time.
SKU: n/a -
Communication Modules, XBee
XBee 1mW Wire Antenna
INTRODUCTION
This is the very popular 2.4GHz XBee module from Digi (formally Maxstream). These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
Pair a couple of these XBees with a Regulated Explorer, and a USB Explorer and you’ve got a great gift for that special electronics geek!SKU: WRE678 -
Communication Modules, XBee
XBee 2mW PCB Antenna – Series 2 (ZigBee Mesh)
This is the XBee XB24-Z7CIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
This Xbee also has a chip antenna which is basically a small chip that acts as an antenna. Quick, easy, cheap, and not in the way.SKU: n/a -
Communication Modules, XBee
XBee 2mW Wire Antenna – Series 2 (ZB)
This is the XBee XB24-Z7WIT-004 module from Digi. Series 2 improves on the power output and data protocol. Series 2 modules allow you to create complex mesh networks based on the XBee ZB ZigBee mesh firmware. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.These are essentially the same hardware as the older Series 2.5, but have updated firmware. They will work with Series 2.5 modules if you update the firmware through X-CTU.
SKU: WRE676 -
Communication Modules, XBee
XBee Pro 60mW PCB Antenna – Series 1
This is the very popular 2.4GHz XBee XBP24-ACI-001 module from Digi. The Pro series have the same pinout and command set of the basic series with an increase output power of 60mW! These modules take the 802.15.4 and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.
SKU: n/a -
Communication Modules, XBee
XBee Pro 60mW Wire Antenna
INTRODUCTION
This is the very popular 2.4GHz XBee XBP24-AWI-001 module from Digi (formerly known as Maxstream). The Pro series have the same pinout and command set of the basic series with an increase output power of 60mW! These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow a very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point networks are supported.SKU: WRE675 -
-
Communication Modules, XBee
Xbee shield V03
This shield V03 can achieve a simple two crunodal ZigBee network, achieve wireless communication between Ardu, and allows the Ardu to wireless communicate over a modified ZigBee protocol using the popular XBee module.It is a fully Assembled shield without the XBee module. It works with all XBee modules including the Series 1 and Series 2.5, standard and Pro versions.SKU: ARD593 -
Arduino & IOT Boards, Mega Payday Sale, Module, Sensors, Temperature, Humidity
XH-M452 Digital Temperature Humidity Controller DC 12v
Arduino & IOT Boards, Mega Payday Sale, Module, Sensors, Temperature, HumidityXH-M452 Digital Temperature Humidity Controller DC 12v
- Supports heating mode and cooling mode.
- High precision 0.1 Celsius and 0.1% RH.
- Real-time display of temperature and humidity.
- Custom load, arbitrarily selected.
- Simple setting.
- Easy installation.
- Power-down memory function.
- Model: XH-M452
- Input voltage: DC 12V
- Temperature range: -20~60 Celsius
- Humidity range: 00%-100% RH
- Detection accuracy: 0.1 Celsius 0.1% RH
- Detection accuracy: 0.1 Celsius
- Sensor: 1 Meter Temperature and humidity sensor
- Output Type: Relay Output (Switch Output)
- Size: 65x55x28mm
SKU: n/a -
Pumps, Sensors, Water, Water Pumps
YF-S401 Water Flow Sensor
- Model: YS-S401
- Working Voltage: DC 5V~24V
- Maximum Working Current: 15mA @ 5V DC
- Flow Rate Range: 0.3~6L/min
- Connection: 6mm (external diameter)
- Inlet Water Pipe Diameter: 2.5-4mm
- Load Capacity: 10mA (DC 5V)
- Operating Temperature: 80
- Liquid Temperature: 120
- Operating Humidity: 35%-90%RH
- Water Pressure: 2.0MPa
- Storage Temperature: -25 to + 80
- Storage Humidity: 25%-95%RH
SKU: n/a -
Communication Modules, XBee
ZigBee XCore2530 1500M
ZigBee module, features the CC2530F256 onboard, farther communication distance with PA
Overview
XCore2530 is a ZigBee module based on CC2530F256.
Basically this module can be used in two aspects :
- Develop application with the provided firmware
Combined with our provided firmware, this is a simple ZigBee wireless UART module, just as easy to use as any other UART module, and requires NO knowledge about the complicate ZigBee Specification - Develop your own firmware
In this case, you should start from the very underlying to create your solution, what’s more, debuggers (like CC Debugger) and knowledge about ZigBee Specification are also required
SKU: n/a - Develop application with the provided firmware
-
Current & Voltage, Sensors
ZMPT 101B Voltage Sensor
- Measure within 250V AC
- Onboard micro-precision voltage transformer
- Analog output corresponding quantity can be adjusted
- Good consistency for voltage and power measurement
- Active output single-phase AC voltage sensor module
- High galvanic isolation
- Wide Range
- High accuracy
SKU: n/a
