Arduino UNO R3 Dip WITH CABLE
Arduino UNO R3 DIP development board with ATmega328P controller and USB programming cable. It provides 14 digital I/O pins, six analog inputs, 5V operation and a familiar UNO layout for electronics learning, robotics, automation and sensor prototypes. This listing is for the board and cable only.
₨ 1,579 ₨ 3,120
Arduino UNO R3 DIP with Cable Price in Pakistan
The Arduino UNO R3 DIP is a practical ATmega328P development board for students, makers and engineers building robotics, automation and embedded-electronics projects. The removable DIP-package controller distinguishes this version from an SMD UNO, while the familiar UNO R3 pin layout supports common shields, sensors and learning examples.
Key specifications
- ATmega328P microcontroller in a removable DIP package
- 5V operating voltage and 16MHz clock
- 14 digital I/O pins, including six PWM outputs
- Six analog input pins
- 32KB Flash, 2KB SRAM and 1KB EEPROM
- Recommended external input: 7V to 12V
- USB programming connection and barrel-jack power input
What is included?
- One Arduino UNO R3 DIP-compatible development board
- One USB programming cable
This board is suitable for LED control, sensor reading, small robots, home-automation prototypes and introductory embedded programming. Check the USB interface and board revision if a computer driver is required, and always match connected modules to the correct logic and supply voltage.
For a breadboard prototype, pair this board with 40-piece male-to-male jumper wires and a GL-12 solderless breadboard.
Browse more Arduino boards in Pakistan from Robonation Pakistan. For board layout and technical limits, review the official Arduino UNO Rev3 documentation.
Based on 0 reviews
Be the first to review “Arduino UNO R3 Dip WITH CABLE”
You may also like…
-
Batteries & Chargers
Powerplus Battery 9V
- Power Plus 9 Volt batteries power everyday devices
- Power for your nonstop family’s must-have devices like toys, flashlights, remotes, and more
- Nominal voltage: 9 V
- Impedance: 1,700 m-ohm @ 1 kHz
- Typical weight: 45 g (1.6 oz)
- Typical volume: 22.8 cm (1.4 in)
- Terminals: Miniature snap
- Operating temperature range: -20ºC to 54ºC (-4ºF to 130ºF)
SKU: n/a -
Bread Board, circuit boards
Breadboard GL-12
- Solder less breadboard with 840 tie points.
- Self-adhesive tape is included on the back, One Terminal Strips Tie-point 640
- Two distribution strips tie-point 200.
- White ABS plastic body with printed legend. The color legend on distribution strips.
- Accept resistors, transistors, diodes, LEDS, capacitors and other types of electronic components.
- Wire size: Suitable for 29-20 AWG wires.
- Size: 175 x 67 x 8 mm
SKU: n/a -
Wires & Connectors
Arduino Jumper Wire M/M 40Pcs
Set of 40 male-to-male jumper wires for solderless breadboards, Arduino-compatible boards and 2.54mm headers. The flexible ribbon can be separated into individual leads or smaller groups, making it useful for reusable circuit prototyping, sensor connections and electronics experiments without soldering.
SKU: n/a -
Mega Payday Sale, Module, Relay Modules, Relay Modules, Relays & Interface Module
1 Channel Relay Module
Mega Payday Sale, Module, Relay Modules, Relay Modules, Relays & Interface Module1 Channel Relay Module
5V single-channel relay module for Arduino-compatible and automation projects. The listed trigger type is high-level input, with at least 4mA drive current. It provides COM, normally open (NO) and normally closed (NC) relay contacts and an on-board status LED. Approximate size: 41 × 16 × 16mm; approximate weight: 12g.
SKU: n/a
Related products
-
-
Arduino & IOT Boards, Module
LM393 Microphone Amplifier
- Detectable sound signal size
- Built-in filter-rectifier circuit, DC signal output
- Good sensitivity, built-in amplifier circuit, adjustable gain
- Voltage signal for sound intensity can be obtained by AD conversion
- Analog voltage signal output, signal amplitude VCC/2
- Compatible for Arduino sensor interface.
SKU: n/a -
Arduino & IOT Boards, Keypads
Keypad 3×4
- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- 5 pins 2.54mm pitch connector, 4×3 type 12 keys.
- Sticker can peel off for adhesive mounting.
- Used widely in industrial and home electronic equipment’s, instrument, etc.
- This allows a microcontroller to ‘scan’ the 7 output pins to see which of the 12 buttons is being pressed.
SKU: n/a -
Arduino & IOT Boards, Boards
Arduino UNO R3 SMD – Economic WITH CABLE
- ATmega328-AU microcontroller with UNO Bootloader Installed.
- USB Programming Facilitated by the CH340G.
- USB-B Connector and cable included.
- Input voltage – 7-15V.
- 0-5V outputs with 3.3V compatible inputs.
- 14 Digital I/O Pins (6 PWM outputs).
- 6 Analog Inputs.
- ISP Header.
- 32k Flash Memory.
- 16MHz Clock Speed.
- All SMD Construction.
- R3 Shield Compatible
SKU: ARD-317
There are no reviews yet.