Module
Showing 25–48 of 75 results
-
Arduino & IOT Boards, Module
Dual-axis XY Joystick Module for Arduino
- Dimensions: 40 x 27 x 15 (LxWxH) mm
- Weight: 10gm (without Hat).
- 2.54mm pin interface leads
- Operating Voltage: 5V.
- Long service life and stable performance
- Standard interface and electronic building blocks
- Widely use in Arduino DIY projects
- Cross rocker as a two-way 10K resistor, with the rocker in a different direction
SKU: n/a -
-
Communication Modules, GSM and GPS
GPS Neo 6m U-Blox NEO-6M GPS Module
- 5Hz position update rate
- Operating temperature range: -40 TO 85C UART TTL socket
- EEPROM to save configuration settings
- Rechargeable battery for Backup
- The cold start time of 38 s and Hot start time of 1 s
- Supply voltage: 3.3 V
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600)
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN)
- Separate GPS antenna
SKU: n/a -
Bluetooth, Communication Modules
HC-05 Bluetooth Module
The HC-05 is a very cool module which can add two-way (full-duplex) wireless functionality to your projects. You can use this module to communicate between two microcontrollers like Arduino or communicate with any device with Bluetooth functionality like a Phone or Laptop. There are many android applications that are already available which makes this process a lot easier. The module communicates with the help of USART at 9600 baud rate hence it is easy to interface with any microcontroller that supports USART. We can also configure the default values of the module by using the command mode. So if you looking for a Wireless module that could transfer data from your computer or mobile phone to microcontroller or vice versa then this module might be the right choice for you.
SKU: n/a -
Bluetooth, Communication Modules
HC-06 Bluetooth Module
HC-06 is a Bluetooth module designed for establishing short range wireless data communication between two microcontrollers or systems. The module works on Bluetooth 2.0 communication protocol and it can only act as a slave device. This is cheapest method for wireless data transmission and more flexible compared to other methods.
SKU: n/a -
Arduino & IOT Boards, Bluetooth, Communication Modules
HC-12 HC12 Si4463 433MHZ RF Wireless Serial Module With Antenna
Arduino & IOT Boards, Bluetooth, Communication ModulesHC-12 HC12 Si4463 433MHZ RF Wireless Serial Module With Antenna
- Working frequency: 433.4MHz to 473.0MHz
- Supply voltage: 3.2V to 5.5VDC
- Communication distance: 1,000m in the open space
- Serial baud rate: 1.2Kbps to 115.2Kbps（default 9.6Kbps）
- Receiving sensitivity: -117dBm to -100dBm
- Transmit power: -1dBm to 20dBm
- Interface protocol: UART/TTL
- Operating temperature: -40℃ to +85℃
- Dimensions: 27.8mm x 14.4mm x 4mm
SKU: n/a -
Arduino & IOT Boards, Kits, Mega Payday Sale, Module, Sensors
High Quality 37 in 1 Sensor Module Board Set Kit For Arduino
Arduino & IOT Boards, Kits, Mega Payday Sale, Module, SensorsHigh Quality 37 in 1 Sensor Module Board Set Kit For Arduino
This 37 in 1 Sensor Module Kit for Arduino is supplied with a variety of sensors that are compatible with Arduino Boards. This is the most complete performance starter kit with all the essential Arduino sensors.
It comprises 37 Pcs of essential Arduino components. The kit includes the latest Arduino components that can be used to turn your idea into a real product.
Tons of updated lessons and Arduino codes are available on Google and YouTube for free. It is extremely easy for Arduino fancier to control and use these modules. This kit will help you control the physical world with sensors.
SKU: n/a -
Arduino & IOT Boards, Communication Modules, Module, RF Modules
HW-237 2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Module with Antenna
Arduino & IOT Boards, Communication Modules, Module, RF ModulesHW-237 2.4GHz NRF24L01+PA+LNA SMA Wireless Transceiver Module with Antenna
- Voltage: 3-3.6V (recommended 3.3V) V.
- Maximum output power: +20dBm.
- Emission mode current(peak): 115mA.
- Receive Mode Current(peak): 45mA.
- Power-down mode current: 4.2uA.
- Sensitivity 2Mbps mode in received: -92dBm.
- Sensitivity 1Mbps mode in received: -95dBm.
- PA gain: 20DbLNA gain: 10Db.
- Sensitivity 250kbps mode in received: -104dBm.
- Operating Range: 1 km
- LNA Noise figure: 2.6 Db.
- Antenna Gain (peak): 2Dbi.
- 2MB rate (Open area): 520m.
- 1MB rate (Open area): 750m.
- 250Kb rate (Open area): 1100m.
- Interface: SPI.
SKU: n/a -
Arduino & IOT Boards, Module
KY-009 RGB LED SMD module
- Using 5050 full-color LED.
- RGB tricolour current一limiting resistance to prevent burnout.
- Through the PWM adjusting three primary colors can be mixed to obtain different colors.
- With a variety of single一chip interfaces.
- Working Voltage: 5V.
- LED Drive Mode: Common cathode driver.
SKU: n/a -
Arduino & IOT Boards, Module, Others, Sensors
KY-021 Mini Magnetic Reed Module for Arduino
- Operating voltage: 3.3V to 5V
- Output type: Digital
- Dimensions: 20 x 15 x 7mm
- Input voltage: 3.3~5v
- Weight: 1.2g
- Reed switch: Normally open
- Reed switch sensitivity: 30 gauss
- Operating temperature: -20°C to 85°C
- Storage temperature: -40°C to 125°C
SKU: n/a -
Arduino & IOT Boards, Drivers, Module
L298N Motor Driver Module
- Driver Model: L298N 2A
- Driver Chip: Double H Bridge L298N
- Motor Supply Voltage (Maximum): 46V
- Motor Supply Current (Maximum): 2A
- Logic Voltage: 5V
- Driver Voltage: 5-35V
- Driver Current:2A
- Logical Current:0-36mA
- Maximum Power (W): 25W
- Current Sense for each motor
- Heatsink for better performance
- Power-On LED indicator
SKU: n/a -
Arduino & IOT Boards, Module
LCD I2C Module IIC/I2C Serial Interface Adapter
- Operating Voltage: 5V
- Backlight and Contrast is adjusted by potentiometer
- Serial I2C control of LCD display using PCF8574
- Come with 2 IIC interface, which can be connected by Dupont Line or IIC dedicated cable
- Compatible for 16×2 LCD
- This is another great IIC/I2C/TWI/SPI Serial Interface
- With this I2C interface module, you will be able to realize data display via only 2 wires.
SKU: n/a -
Module, Relay Modules, Relay Modules, Relays & Interface Module
Light Sensitive LDR Relay Module 12V
- Automatically controls the relay based on light intensity
- Included LDR (Light Dependent Resistor) sensor on 10 lead detects visible light
- Adjustable light level set-point
- Controls loads of 115/230VAC @ 10A
- Controls loads of 0 15VDC @ 10A
- Both NO (Normally Open) and NC (Normally Closed) contacts
- LED indicator when the relay is energized
- 12V power operation
SKU: n/a -
Arduino & IOT Boards, Module
LM393 Microphone Amplifier
- Detectable sound signal size
- Built-in filter-rectifier circuit, DC signal output
- Good sensitivity, built-in amplifier circuit, adjustable gain
- Voltage signal for sound intensity can be obtained by AD conversion
- Analog voltage signal output, signal amplitude VCC/2
- Compatible for Arduino sensor interface.
SKU: n/a -
Arduino & IOT Boards, Module
Logic Level Converter
The logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. A Logic Level Converter is very easy to connect and use since it doesn’t need any programming, all you have to do is connect the 5V wire on one side and the 3.3V on the other.
SKU: n/a -
Arduino & IOT Boards, Module
MAX31865 RTD PT100 Amplifier
- Advantage: Handling all of your RTD needs.
- Strong point: Compensating 3 or 4-wire RTDs for better accuracy.
- Characteristic: Could be used with any Arduino or microcontroller.
- Feature: 3.3V regulator and level shifting.
- Feature: Could be used with any 2, 3, or 4-wire PT100 RTD.
SKU: n/a -
Arduino & IOT Boards, Module
MAX7219 Dot LED Matrix 4×1 Module MCU Control Unit
- MAX7219 is an integrated serial input / output common-cathode display driver, it connects the microprocessor 7-segment digital LED display with 8 digits, you can also connect a bar graph display or 64 independent LED. Thereon including a B-type BCD encoder chip, multi-channel scanning loop segment word driver, but also a static RAM 8 * 8 for storing each data. Only one external register is used to set the segment current of each LED.
- A convenient four-wire serial interface can be connected to all general-purpose microprocessor. Each data can be addressed in the update do not need to rewrite all of the display. MAX7219 also allows each user to select a data coding or non-coding.
- The entire device contains a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display data bits 1-8, and one for all LED luminescence detection mode.
- It requires only three IO ports to drive a dot matrix! No flicker when the dot matrix display! Support cascading!
SKU: n/a -
Arduino & IOT Boards, Converters, Module
MT3608 Step-Up Adjustable DC-DC Switching Boost Converter
- Input Voltage: 2-24V DC
- Output Voltage: 5-28V DC
- Maximum Output Current: 2A
- Switching Frequency: 1.2Mhz
- Output Ripple: <100mV
- Module Size: 37.2mm x 17.2mm x 14.0mm
- About 93% Efficiency
- Features like an under-voltage lockout, thermal overload protection
SKU: n/a -
Communication Modules, RF Modules
NRF24L01 2.4GHz Wireless Transceiver Module
- Worldwide 2.4GHz ISM band operation Free license to use.
- 126 RF channels.
- High air data rate: 250kbps, 1 and 2Mbps.
- Transmitter: 11.3mA at 0dBm output power.
- Receiver: Fast AGC for improved dynamic range.
- Receiver: Integrated channel filters.
- Enhanced ShockBurst:1 to 32 bytes dynamic payload length,6 data pipe MultiCeiver for 1:6 star networks.
- Host Interface:4-pin hardware SPI,3 separate 32 bytes TX and RX FIFOs.
- Low Power Management:1.9 to 3.6V supply range.
- GFSK modulation.
- Auto packet transaction handling.
- Easy to design.
- Small size:15mm*29mm.
SKU: WRE335 -
Communication Modules, RF Modules
NRF24L01 Antenna Pair
This is NRF24L01 2.4GHz Antenna Wireless Transceiver Module. The nRF24L01 is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub 26A power down mode, advanced power management, and a 1.9 to 3.6V supply range, the nRF24L01 provides a true ULP solution enabling months to years of battery life when running on coin cells or AA/AAA batteries. These RF modules are very popular among the Arduino tinkerers. The nRF24L01 is used on a wide variety of applications that require wireless control. They are transceivers which this means that each module can transmit and receive data.
SKU: n/a -
Breakout Boards
nRF24L01 Breakout Adapter with On-board 3.3V Regulator
- Addicore nRF24L01+ Breakout Adapter with onboard 3.3V Regulator
- On-board 3.3V voltage regulator accepts your Arduino +5V supply and provides 3.3V for the attached nRF24L01+ module
- Allows for easy connection to nRF24L01+ modules
- Small power on SMD LED indicator
- On-Board Voltage Regulator: Voltage Regulator Input Voltage (connected to VCC): 4.8V to 12V
- Voltage Regulator Input Voltage Max: 15V (we recommend staying below 12V)
SKU: n/a -
Arduino & IOT Boards, Module, Sensors, Water
Ph Sensor Gravity Sensor Module
- Module Power: 5.00V
- Module Size : 43 x 32mm(1.69×1.26″)
- Measuring Range :0 – 14PH
- Measuring Temperature: 0 – 60 ℃
- Accuracy : ± 0.1pH (25 ℃)
- Response Time: ≤ 1min
- pH Sensor with BNC Connector
- pH2.0 Interface ( 3 foot patch )
- Gain Adjustment Potentiometer
- Power Indicator LED
SKU: n/a
