Common Components
Showing 289–336 of 346 results
-
ICs
MC1496 IC – Balanced Modulator/Demodulator
This device is designed for use where the output voltage is a product of an input voltage (signal) and a switching function (carrier). Typical applications include suppressed carrier and amplitude modulation, synchronous detection, FM detection, phase detection, and chopper applications.
SKU: n/a -
ICs
MC34063
The MC34063A Series is a monolithic control circuit containing the primary functions required for dc-to-dc converters. These Buck Boost Inverting Switching Regulators consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. Operation from 3.0 V to 40 V Input. Output Switch Current to 1.5 A.
SKU: n/a -
-
Variable/Potentiometer
Multiturn Variable Potentiometer 10K
Multiturn Variable Potentiometer 10K / Variable Resistor. There are lots of trimpots out there. Some are very large, some so small they require a screwdriver. Here at ELECTRONATION, we just needed a simple one that worked. This 10K trimmable potentiometer has a small knob built right in and it’s breadboard friendly to boot! Perfect for your next LCD contrast adjuster, opamp setting, or volume level. This is 3296W model 103 within the datasheet.
SKU: n/a -
Variable/Potentiometer
Multiturn Variable Potentiometer 1K
A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer.
SKU: n/a -
Variable/Potentiometer
Multiturn Variable Potentiometer 5K
A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer.
SKU: n/a -
ICs
NE556 Dual Timer IC
- A dual version of NE556 consists of two precision timers that operate in both monostable and astable modes.
- It is specified for operation from 4.5 V to 16 V.
- TTL compatible output which can source or sink current of up to 150mA.
- Adjustable duty cycle.
- It can produce a timing delay from microseconds to hours.
- The operating temperature range is from 0 to 70 degrees Celsius.
- It has temperature stability better than 0.005% per C.
SKU: n/a -
ICs
OPTOCOUPLER 817 QUAD
Optocoupler 817 QUAD contains an IRED optically coupled to a phototransistor. It is packaged in a 4pin DIP, available in wide-lead spacing option and SMT gullwing lead-form option. Input-output isolation voltage(rms) is 5.0kV. Collector-emitter voltage is 80V(*) and CTR is 50% to 600% at input current of 5mA.
SKU: n/a -
ICs
PIC 16F877 Microcontroller
This robust (200 nanosecond instruction execution) yet easy-to-program (only 35 single word instructions) CMOS FLASH-based 8-bit microcontroller packs Microchip’s robust PIC® architecture into a 40- or 44-pin package. It is upwards compatible with the PIC16C5X, PIC12CXXX and PIC16C7X devices. The PIC16F877A features 256 bytes of EEPROM data memory, self-programming, an ICD, 2 Comparators, 8 channels of 10-bit Analog-to-Digital (A/D) converter, 2 capture/compare/PWM functions, the synchronous serial port can be configured as either 3-wire Serial Peripheral Interface (SPI™) or the 2-wire Inter-Integrated Circuit (I²C™) bus and a Universal Asynchronous Receiver Transmitter (USART). These features make it ideal for more advanced level A/D applications in automotive, industrial, appliances and consumer applications.
SKU: n/a -
Variable/Potentiometer
Potentiometer 22K OHM
A potentiometer is a manually adjustable variable resistor with 3 terminals. Two terminals are connected to both ends of a resistive element, and the third terminal connects to a sliding contact, called a wiper, moving over the resistive element. The position of the wiper determines the output voltage of the potentiometer.
SKU: n/a -
Diodes
Red laser 5V 650nm wire
This laser pointer or laser pen is a small handheld device with a laser diode emitting a very narrow coherent low-powered laser beam of visible light, it is frequently used in lecture halls and demonstrations to point at topics of interest on a presentation board. In a school setting, they have become ubiquitous, and they are very useful teaching aids.
SKU: n/a -
Voltage Regulators
Regulator, Step-Down Switching, Adjustable Output Voltage, 1.0 A LM2575, NCV2575
- 3.3 V, 5.0 V, 12 V, 15 V, and Adjustable Output Versions
- Adjustable Version Output Voltage Range of 1.23 V to 37 V 4% Maximum Over Line and Load Conditions
- Guaranteed 1.0 A Output Current
- Wide Input Voltage Range: 4.75 V to 40 V
- Requires Only 4 External Components
- 52 kHz Fixed Frequency Internal Oscillator
- TTL Shutdown Capability, Low Power Standby Mode
- High Efficiency
- Uses Readily Available Standard Inductors
- Thermal Shutdown and Current Limit Protection
- Moisture Sensitivity Level (MSL) Equals 1
- NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable
- These are Pb−Free Devices
SKU: n/a -
Rectifiers
SCR C106 C106 Series – SCR TO-255AA 4A
- Glassivated Surface for Reliability and Uniformity
- Power Rated at Economical Prices
- Practical Level Triggering and Holding Characteristics
- Flat, Rugged, Thermopad Construction for Low Thermal Resistance, High Heat Dissipation and Durability
- Sensitive Gate Triggering
- Device Marking: Device Type, e.g., C106B, Date Cod
SKU: n/a -
ICs
Serial EEPROM AT24C02
- Low-voltage and Standard-voltage Operation
- 2.7 (VCC = 2.7V to 5.5V)
- 1.8 (VCC = 1.8V to 5.5V)
- Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K),
- 1024 x 8 (8K) or 2048 x 8 (16K)
- Two-wire Serial Interface
- Schmitt Trigger, Filtered Inputs for Noise Suppression
- Bidirectional Data Transfer Protocol
- 100 kHz (1.8V) and 400 kHz (2.7V, 5V) Compatibility
- Write Protect Pin for Hardware Data Protection
- 8-byte Page (1K, 2K), 16-byte Page (4K, 8K, 16K) Write Modes
- Partial Page Writes Allowed
- Self-timed Write Cycle (5 ms max)
- High-reliability
- Endurance: 1 Million Write Cycles
- Data Retention: 100 Years
- Automotive Devices Available
- 8-lead JEDEC PDIP, 8-lead JEDEC SOIC, 8-lead Ultra Thin Mini-MAP (MLP 2×3), 5-lead SOT23, 8-lead TSSOP and 8-ball dBGA2 Packages
- Die Sales: Wafer Form, Waffle Pack and Bumped Wafers
SKU: n/a - Low-voltage and Standard-voltage Operation
-
Common Components, ICs
SG3525 / KA3525 PWM Controller IC in Pakistan
- DUAL SOURCE/SINK OUTPUT DRIVERS
- LATCHING PWM TO PREVENT MULTIPLE PULSES
- PULSE-BY-PULSE SHUTDOWN
- INTERNAL SOFT-START
- 8 TO 35 V OPERATION
- 100 Hz TO 500 KHz OSCILLATOR RANGE
- 5.1 V REFERENCE TRIMMED TO 1 %
- ADJUSTABLE DEADTIME CONTROL
- INPUT UNDERVOLTAGE LOCKOUT WITH HYSTERESIS
- SEPARATE OSCILLATOR SYNC TERMINAL
SKU: n/a -
ICs
SN74125 Buffer & Line Driver IC
- Technology Family: LS
- VCC (Min): 4.75V
- VCC (Max): 5.25
- Channels (#): 4
- Operating Voltage (Nom): 5V
- Frequency at normal voltage (Max): 35MHz
- Propagation delay (Max): 20ns
- IOL (Max): 24mA
- IOH (Max):-2.6mA
- Input Type: Bi-polar
- Output type: 3-State
- High speed (tpd 10-50ns)
- Rating: Catalog
- Data rate: 70Mbps
- Available in 14-pin PDIP, GDIP, PDSO packages
SKU: n/a -
ICs
SN74HC241 Buffer & Line Driver IC
These octal buffers and line drivers are designed specifically to improve both the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters. The HC241 devices are organized as two 4-bit buffers/drivers with separate output-enable (1OE and 2OE) inputs. When 1OE is low or 2OE is high, the device passes noninverted data from the A inputs to the Y outputs. When 1OE is high or 2OE is low, the outputs for the respective buffers/drivers are in the high-impedance state.
SKU: n/a -
ICs
SN74LS138 Demultiplexer IC
- Technology Family: LS
- Rating: Catalog
- Supply voltage: 1.0V to 5.5V
- Frequency at nominal voltage: 35 MHz
- Typical propagation delay: 21nS
- Low power consumption: 32mW
- Operating temperature: -40ºC to +125ºC
- ESD protection
- Balanced propagation delays
- Designed specifically for high speed
- Channels (#): 1
- Configuration: 3:8
- Product type: Standard
SKU: n/a -
Transistors & Mosfet
TIP122 – Darlington Transistor (Original)
- Darlington medium-power NPN Transistor
- High DC Current Gain (hFE), typically 1000
- Continuous Collector current (IC) is 5A
- Collector-Emitter voltage (VCE) is 100 V
- Collector-Base voltage (VCB) is 100V
- Emitter Base Voltage (VBE) is 5V
- Base Current(IB) is 120mA
- Type NPN
- Collector-Emitter Voltage: 100V
- Collector-Base Voltage: 100V
- Emitter-Base Voltage: 5V
- Collector Current: 5A
- Collector Dissipation: 65W
- DC Current Gain (hfe): 1000
- Operating and Storage Junction Temperature Range: -65 to +150C
- Package: TO-220
SKU: n/a -
ICs
TL082 TL082CN Operational Amplifier OPA IC in DIP-8 Package
- Carries Low input bias current = 50 pA
- Available with Low input noise current = 0.01 pA/Hz
- Comes with Fast settling time to 0.01% = 2us
- Contains internally trimmed offset voltage = 15 mV
- Carries Low input noise voltage = 16nV/Hz
- Exhibits Low supply current = 3.6 mA
SKU: n/a -
-
ICs
TL431 Shunt Regulator
The TL431 is three-terminal adjustable shunt regulators, with specified thermal stability over applicable automotive, commercial, and military temperature ranges. The output voltage can be set to any value between Vref (approximately 2.5 V) and 36 V, with two external resistors. These devices have a typical output impedance of 0.2 .
SKU: n/a -
ICs
TL494 Current-Mode PWM Controller
The TL494 device incorporates all the functions required in the construction of a pulse-width-modulation (PWM) control circuit on a single chip. Designed primarily for power-supply control, this device offers the flexibility to tailor the power-supply control circuitry to a specific application. The TL494 device contains two error amplifiers, an on-chip adjustable oscillator, a dead-time control (DTC) comparator, a pulse-steering control flip-flop, a 5-V, 5%-precision regulator, and output-control circuits.The TL494C device is characterized for operation from 0C to 70C. The TL494I device is characterized for operation from 40C to 85C.
SKU: n/a -
ICs
TLP250 MOSFET IGBT DRIVER TLP-250
- Input threshold current: IF=5mA(max.)
- Supply current (ICC): 11mA(max.)
- Supply voltage (VCC): 1035V
- Output current (IO): 1.5A (max.)
- Switching time (tpLH/tpHL): 1.5s(max.)
- Isolation voltage: 2500Vrms(min.)
- UL recognized: UL1577, file No.E67349
- Option (D4) type
- VDE approved: DIN VDE0884/06.92,certificate No.76823
- Maximum operating insulation voltage: 630VPK
- Highest permissible over voltage: 4000VPK
- Creepage distance: 6.4mm(min.)
- Clearance: 6.4mm(min.)
SKU: n/a -
Transistors & Mosfet
Transistor Heat Sink
A heat-sink is designed to remove heat from a transistor and dissipate it into the surrounding air as efficiently as possible. Heat-sinks take many different forms, such as finned aluminium or copper sheets or blocks, often painted or anodised matt black to help dissipate heat more quickly. Good physical contact between the transistor and heat-sink is essential, and a heat transmitting grease (heat-sink compound) is smeared on the contact area before clamping the transistor to the heat-sink.
SKU: n/a -
ICs
UA723
The uA723 is a precision integrated-circuit voltage regulator, featuring high ripple rejection, excellent input and load regulation, excellent temperature stability, and low standby current. The circuit consists of a temperature-compensated reference-voltage amplifier, an error amplifier, a 150-mA output transistor, and an adjustable-output current limiter.The uA723 is characterized for operation from 0C to 70C.
SKU: n/a -
-
ICs, Transistors & Mosfet
ULN 2803
ULN 2803 is a high-voltage, high-current Darlington transistor array. The device consists of eight npn Darlington pairs that feature high-voltage outputs with common-cathode clamp diodes for switching inductive loads. The collector-current rating of each Darlington pair is 500 mA. The Darlington pairs may be connected in parallel for higher current capability. Applications include relay drivers, hammer drivers, lamp drivers, display drivers (LED and gas discharge), line drivers, and logic buffers.
SKU: n/a -
ICs, Transistors & Mosfet
ULN2003 IC
- Seven Darlingtons per package
- Output current 500 mA per driver (600 mA peak)
- Output voltage 50 V
- Integrated suppression diodes for inductive loads
- Outputs can be paralleled for higher current
- TTL/CMOS/PMOS/DTL compatible inputs
- Inputs pinned opposite outputs to simplify
SKU: n/a
TL431 Shunt Regulator
DIP Switch 6 Positions
CD4051 Single 8-channel Multiplexer Demultiplexer
TL494 Current-Mode PWM Controller
OPTOCOUPLER 817 QUAD
BT151 Thyristor
MC34063
MCP23S17 I/O Expander IC 







































