-
×
Vero Board Normal Dots
1 × ₨ 99 -
×
IR Infrared sensor Two way Obstacle Sensor
1 × ₨ 109
Subtotal: ₨ 208
-19%
IR & Vision, Sensors
Infrared receiver KY-022
- Voltage: 3.3V to 5V
- Characteristics: 700nm x 1mm
- Chipset: TSOP1838 37.9kHz
- Daylight Rejection: up to 500LUX
- Receiving Distance: up to 18 m
- Size: 19mm x 15mm x 14mm
₨ 169 ₨ 208
Infrared receiver KY-022
Parameters:
- Voltage: 3.3V to 5V
- Characteristics: 700nm x 1mm
- Chipset: TSOP1838 37.9kHz
- Daylight Rejection: up to 500LUX
- Receiving Distance: up to 18 m
- Size: 19mm x 15mm x 14mm
Infrared receiver KY-022 Features:
The KY-022 module is ideally suitable for infrared light detection within the range of 700nm x 1mm, which is typically seen in project robots and remote control receivers.
The data pin outputs HIGH when the sensor is triggered.
Working at a low 3.3 to 5V input the module will output HIGH values on detecting a signal and LOW values while not detecting
A data LED is mounted onto the board that lights up when the sensor is triggered.
Based on 0 reviews
Be the first to review “Infrared receiver KY-022”
Related products
-
Accelero, Gyro. IMU, Magneto, Sensors
10 DOF IMU Sensor
3 Axis Accelerometer + 3 Axis Gyroscope + 3 Axis Magnetometer + Pressure Sensor on one board i.e.
ADXL 345+L3G4200D+HMC5883L+BMP085 sensors all in one board. There are also a 2.5V voltage regulator, the logic level converter circuit to make it work under the power of 3V-5V. Thanks to the logic level converter circuit, you can connect it with a 3V-5V MCU directly, just plug and play! Also every interrupt pin of the sensors is leaded out.
SKU: n/a -
Heart Rate And Muscle Sensors, Sensors
Biomedical Sensor Pad (10 pack)
This is a 10 pack of Biomedical Sensor Pads, disposable electrodes that can be used to measure EEG, ECG and EMG levels. these little pads are perfect for short-term monitoring of Neurofeedback and Biofeedback purposes. They are to be used once and are very handy because of integrated, latex-free gel. Each pad adheres very well to the skin and the snap connector can be pushed on or removed from the electrode lead with no issue.
SKU: n/a -
Gas Sensor, Sensors
MQ135 Air Quality Detector Sensor Module
- Air Quality Sensor Module
- Condition: New
- Size: 32mm X22mm X27mm
- Main chip: MQ-135
- Operating Voltage: 5V DC
- Type: Analog & Digital
- Sensitivity to Ammonia, Sulphide and Benzene steam
- Detecting Range: 100-1000ppm
- With signal output instructions
- TTL output signal is low level
- Analog 0 ~ 5 v voltage output, the higher the concentration, the higher the voltage
- Color is showing pictures.
- Sensitive for benzene, alcohol, smoke
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Output voltage boosts along with the concentration of the measured gases increases
SKU: n/a -
Others, Sensors
Microphone Amplifier – MAX9814 w/ Auto Gain Control
- The default ‘max gain’ is 60dB, but can be set to 40dB or 50dB by jumpering the Gain pin to VCC or ground.
- You can change the Attack/Release ratio, from the default 1:4000 to 1:2000 or 1:500.
- The ouput from the amp is about 2Vpp max on a 1.25V DC bias, so it can be easily used with any Analog/Digital converter that is up to 3.3V input. If you want to pipe it into a Line Input, just use a 1uF blocking capacitor in series.
SKU: n/a
There are no reviews yet.