Shop
Showing 385–432 of 1337 results
-
Motors, Multicopter Accesories
A2212 1000KV Brushless DC Motor
- Model: A2212 10T
- Motor KV (RPM/V): 1400
- Maximum Efficiency: 80%
- Current Capacity: 16A Per 60S
- No-Load Current(A): 0.7A @10V
- Max. Efficiency Current: 6-12A
- Maximum Watts(W): 180
- Internal Resistance(mΩ): 65
- Poles: 14
- Shaft Diameter (mm): 3.17
- LiPO Batteries: 2S-3S
- Length (mm): 27.5
- Width (mm): 26.5
- Weight (gm): 62
SKU: n/a -
BLDC Motor, Motors, Motors & Drivers, Multicopter Accesories
A2212 2200KV Brushless DC Motor BLDC
- Recommended Voltage: 2-12VDC
- Internal Resistance: 90mΩ
- Shaft Size: 3.17mm (1.8″)
- Shaft Length: 11mm
- Motor Diameter: 27.5mm
- Motor Length (Overall): 40mm
- Current Capacity: 12A/60s
- Max Efficiency: 80%
- Max Power: 239W
- Recommended ESC: Minimum Of 18A
- Recommended Model Weight: 300-1000g
- Mounting Holes: M3
- Wire Length: ~70mm
SKU: n/a -
Arduino & IOT Boards, Drivers, Module
A3967 Stepper Motor Driver Module
This EasyDriver compatible stepper motor driver module utilizes the Allegro A3967SLB micro-stepping driver to proved a simple and compact means of driving bi-polar motors, and motors wired as bi-polar. I.e. 4,6, or 8 wire stepper motors from a microcontroller. By default, the module will accept a 5V TTL step and direction signal from the microcontroller to stop the motor in either full, half, quarter, and eighth-step modes. By shorting jumper SJ2 it can also be configured to be compatible with 3.3V microcontrollers that are not 5V tolerant. An onboard potentiometer allows for setting maximum drive current.
SKU: n/a -
Motor Drivers, Motor Drivers, Motors & Drivers, Robotics
A4988 Stepper driver
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection/choice.
- Mixed with slow current decay mode.
- The low power dissipation of synchronous rectifier.
- Internal UVLO(ultra voltage lockout).
- Crossover current protection.
- Thermal shutdown circuit.
- Ground fault protection.
- Loading and short circuit protection.
- The optional five-step mode: full, 1/2, 1/4, 1/8 and 1/16.
SKU: n/a -
Batteries & Chargers, Holders
AA 4 Battery Holder
AA 4 Cell Battery Holder Need 6V 1.5V cell or 4.8V with 1.2V cell to run a project on AA batteries This is a simple battery holder that we use in some of our kits. What we like about these are the leads that come pre-attached, ready to be soldered to a PCB, or attached with your choice of connector.
- Two mounting holes to accept flush head screws.
- You can also use high adhesive double-sided tape, or a glue gun to attach to your project or prototype.
- This battery holder has two wires 6 inches of 24-gauge leads that have 5 mm of insulation stripped off of the ends.
SKU: n/a -
Cases & Enclosure
ABS Enclosure Black Case for Raspberry Pi with Heat Sink And 5v Fan
This Raspberry case is made of ABS material. It can be perfectly compatible with Raspberry Pi 4B. Considering the high power consumption cost of Raspberry Pi 4B, the Raspberry case has room to add a fan (35x35x10mm) and general copper/aluminum heatsink (up to 6mm) for heat dissipation. What’s more The case supports the GPIO PINs of the Raspberry Pi 4B and connects external devices like Raspberry Pi Hat outside the case by cables. Also, the ventilation openings are designed on the top and bottom of the case to keep cooling.
SKU: n/a -
-
Incubator, Temperature & Humidity Controllers
AC 220V Temperature Controller RKC REX-C700
- Type: Digital
- Theory: Temperature Controller
- Usage: Industrial
- Model Number: REX-C700 Power
- Type: Charger Display
- Size:1.9 Inches & Under Max
- Measuring Temperature:120°C & Above
- Style: Standing Station
- Size:72*72mm
- Input: Universal Control
- output: Relay Alarm
- Display: Celsius °C Unit
- Type: piece
- Package Weight: 0.4kg (0.88lb.)
SKU: n/a -
-
Current & Voltage, Sensors
ACS712 Current Sensor 20A
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -20A~ 20A
- Sensitivity: 100mV/A
- The current sensor chips: ACS712_ELC-20A.
- Pin 5V power supply, onboard power indicator.
- There is no the detection current through, the output voltage is VCC / 2.
- The module can be measure plus or minus 20 amps, corresponding to the analog output of 185 mV / A.
SKU: n/a -
Current & Voltage, Sensors
ACS712 Current Sensor 30A
ACS712 Current Sensor 30A current sensor board is based on the Allegro ACS712ELCTR-30A bi-directional hall-effect current sensor chip that detects positive and negative flowing currents in the range of minus 30 Amps to positive 30 Amps. The board operates at 5V DC and the current flow through the sensor is converted to an output voltage starting at 1/2Vcc (or 2.5V) for no current flow and moves up 66mV per amp for positive current or down -66mV per amp for negative current.
SKU: n/a -
Current & Voltage, Sensors
ACS712 Current Sensor 5A
- Module Dimensions: 31 x 13 x 14 mm (LxWxH)
- Weight: 3 gm.
- Supply Voltage: 4.5V~5.5V DC
- Measure Current Range: -5A~ 5A
- Sensitivity: 66mV/A
- The current sensor chips: ACS712_ELC-05B.
- Pin 5V power supply, onboard power indicator.
- There is no the detection current through, the output voltage is VCC / 2.
SKU: n/a -
ICs
AD7528 DAC IC
The AD7528 is a monolithic dual 8-bit digital/analog converter featuring excellent DAC-to-DAC matching. It is available in skinny 0.3″ wide 20-lead DIPs and in 20-lead surface mount packages. Separate on-chip latches are provided for each DAC to allow easy microprocessor interface.
SKU: n/a -
Arduino & IOT Boards, Module
ADS1115 Analog-to-Digital Converter
- WIDE SUPPLY RANGE: 2.0V to 5.5V
- LOW CURRENT CONSUMPTION: Continuous Mode: Only 150µA Single-Shot Mode: Auto Shut-Down
- PROGRAMMABLE DATA RATE: 8SPS to 860SPS
- INTERNAL LOW-DRIFT VOLTAGE REFERENCE
- INTERNAL OSCILLATOR
- INTERNAL PGA
- I2C INTERFACE: Pin-Selectable Addresses
- FOUR SINGLE-ENDED OR TWO DIFFERENTIAL INPUTS
- PROGRAMMABLE COMPARATOR
- This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers
SKU: n/a -
Others, Sensors
AH175 Hall Sensor
Hall effect sensor is transducing devices used to detect and generate a voltage when in the presence of a magnetic field. They are designed to induce a voltage as an output when a magnetic field is present at its input. The output voltage can be variable depending on the magnitude of the magnetic field. Hall effect sensors, as they name states are effect sensors, which can be used to sense different categories, like speed, position of objects, rotational speed or frequency and be used as a fault detector. They can be used to detect a time-varying current, as time-varying current produce magnetic fields, which can then be sensed by the Hall effect transducer and produce a voltage with some proportion the amount of magnetic field present at the sensor.
SKU: n/a -
Solder Paste, Soldering Accessories & Tools
AMTECH RMA223 RMA-223 RMA559 Solder Paste Flux 10CC
- Flux Type: Original AMTECH RMA-223 UV (Made in USA)
- Volume: 10ml/10cc
- Dimension: 93 x 33 x 23mm
- Material: the mixture of high-quality alloyed powder and resinic pasty flux, it can avoid the pale yellow residue.
- Color: Colorless/Transparent
- Insulated: Yes
- With Needle Tip: Yes
- Made in: USA
- Application: for soldering and reballing of computer and phone chips.
- Advantage: Good immersion and high-intensity joint.
- Function: for PCB, BGA, and PGA reworking.
- 100%: New Type, high quality.
SKU: n/a -
-
-
-
-
Digital Meter, Multi Meters
ANENG ST212 Digital DC/AC Clamp Meter Current 400A Amp Multimeter Large Color Screen
Digital Meter, Multi MetersANENG ST212 Digital DC/AC Clamp Meter Current 400A Amp Multimeter Large Color Screen
- AC Current Range: 60A/400A
- DC Current Range: 60A/400A
- DC Voltage Range: 600V/600mV
- AC Voltage Range: 600V/600mV
- Resistance: 600Ω/6kΩ/60kΩ/600kΩ/6MΩ/60MΩ
- Capacitance: 60nF/600nF/6uF/60uF/600uF/6mF/60mF
- Temperature: -40~1000℃, -40~1832℉
- Frequency: 60Hz/1000Hz
- Colour: Red
- Material: ABS
- Display: LCD
- Max. Display Value: 6000 digit
- Sampling Time: About 3 times/second, bargraph 10 times/second
- Auto-off: 15 minutes
- Operating Temperature: 18~28℃
- Storage Temperature: -10~50℃
- Operating Height: Max. 2000m
- Power Supply: 2 * 1.5V AAA battery (NOT included)
- Item Size: 182 * 62.1 * 33.4mm / 7.17 * 2.44 * 1.31in
- Item Weight: 150g / 5.29oz
- Package Weight: 272g / 9.59oz
- Package Size: 21.7 * 8.5 * 4.5cm / 8.54 * 3.35 * 1.77in
SKU: n/a -
Distance & Proximity, Light, Sensors
APDS9960 proximity and light intensity sensor I2C 3.3V
- Gesture recognition using reflected IR
- Digital proximity sensing using reflected IR
- Separate Red/Green/Blue light intensity sensors
- Ambient (clear) light intensity sensor
- IR light-blocking filter
- Interrupt output available
- I2C interface with good library support
- 3.3V operation
SKU: n/a -
Flight Controller, Multicopter Accesories
APM Power Module
The power module has the ability to provide APM lossless power from a LiPo battery as well as current consumption and voltage measurements through 6-pos cable. The on board regulator switch has the ability of giving outputs 5.3V and a maximum of 2.25A from up to a 4S LiPo battery.
SKU: n/a -
Flight Controller, Multicopter Accesories
APM2.6 Flight Controller
The ArduPilot Mega 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. This version is ready to use, with no assembly required. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints.
This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it’s often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass, so that the GPS/Compass unit can be mounted further from noise sources than APM itself.
SKU: n/a -
Flight Controller, Multicopter Accesories
APM2.8 ArduPilot Mega 2.8 Flight Control Board
This is the new APM 2.8 autopilot module. The sensors are exactly the same as with APM2.6, however this version does not have an onboard compass, which makes this version ideal for use with multicopters and rovers.
It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.
SKU: n/a -
Arduino & IOT Boards, Module, Motors & Drivers, Stepper Motor
Arduino 28BYJ48 Stepper Motor
Arduino 28BYJ48 Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug. Motor: Diameter: 28mmVoltage: 5VStep angle: 5.625 x 1/64Reduction ratio: 1/64ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31x35mmPackage included:1 x ULN2003 driver board1 x 28BYJ-48 stepper motor Options:
SKU: n/a -
-
Arduino & IOT Boards, Shields
ARDUINO CNC SHIELD V3
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
SKU: n/a -
Arduino & IOT Boards, Boards
Arduino Due AT91SAM3X8E ARM Cortex-M3 Board
- MicrocontrollerAT91SAM3X8E
- Operating Voltage3.3V
- Input Voltage (recommended)7-12V
- Input Voltage (limits)6-16V
- Digital I/O Pins54 (of which 12 provide PWM output)
- Analog Input Pins12
- Analog Output Pins2 (DAC)
- Total DC Output Current on all I/O lines130 mA
- DC Current for 3.3V Pin800 mA
- DC Current for 5V Pin800 mA
- Flash Memory512 KB is all available for the user applications
- SRAM96 KB (two banks: 64KB and 32KB)Clock Speed84 MHz
- Length101.52 mm
- Width53.3 mm
- Weight36 g
SKU: n/a -
Wires & Connectors
Arduino Jumper Wire F/F 40Pcs
- 40 pieces of the 10cm female to female color Dupont jumper wires cables in one set will be sold together.
- Color: as shown in the pictures.
- Material: durable hard plastic and copper wire.
- Each cable length: about 10cm /3.94 .
- Connectors: 1pin-1pin female to female header.
- 100% brand new and high quality 2.54mm Female to Female Color Dupont Jumper Wires Cables for Arduino Breadboard.
- Compatible with 2.54mm spacing pin headers.
- A popular choice for the construction or repair.
- Can be used for electronic project and Genuine Arduino products.
- Easy to install and use, durable and reusable to use.
SKU: n/a -
Wires & Connectors
Arduino Jumper Wire M/F 40Pcs
- Color: Multicolor.
- Material: durable hard plastic andcopper wire.
- Each cable length: about 10cm /3.94/.
- Connectors: 1pin-1pin male to female header.
- 100% brand new and high quality 2.54mm Male to Female Color Dupont Jumper Wires Cables for Arduino Breadboard.
- Compatible with 2.54mm spacing pin headers.
- A popular choice for the construction or repair.
- Can be used for electronic project and Genuine Arduino products.
- Easy to install and use, durable and reusable to use.
SKU: n/a -
Wires & Connectors
Arduino Jumper Wire M/M 40Pcs
- Compatible with 2.54 mm spacing pin headers.
- 120 pcs chromatic color jump wire.
- High quality and in good working condition.
- Durable and reusable.
- Easy to install and use.
- A popular choice for construction or repair.
- Be used for the electronic project and Genuine Arduino product.
- Flexible Breadboard Jumper Cable Wire allows you to plug and unplug easily for prototyping.
SKU: n/a -
Arduino & IOT Boards, Boards
Arduino Leonardo R3
he Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
SKU: ARD-452 -
Arduino & IOT Boards, Boards
Arduino MEGA 2560 PRO Mini
- Microcontroller ATmega2560
- USB-TTL converter: CH340
- Power Out:5V-800mA
- Power IN.: 5V
- Power IN. VIN/DC Jack:5V
- Power Consumption: 5V 220mA
- Logic Level: 5V
- USB: Micro USB
- Clock Frequency: 16MHz
- Operating Supply Voltage: 5V
- Digital I/O: 54
- Analog I/O: 16
- Memory Size: 256kb
- Data RAM Type/Size: 8Kb
- Data ROM Type/Size: 4Kb
- Interface Type : ISP
- Operating temperature 40C/+85C
- Length x Width:38mmx54mm
SKU: n/a -
-
-
Arduino & IOT Boards, Boards
Arduino Nano V3
- Microcontroller: Atmel ATmega168 or ATmega328.
- Operating Voltage (logic level): l5 V.
- Input Voltage (recommended): 7-12 V.
- Input Voltage (limits): 6-20 V.
- Digital I/O Pins: 14 (of which 6 provide PWM output).
- Analog Input Pins: 8.
- DC Current per I/O Pin: 40 mA.
- Flash Memory: 16 KB (ATmega168) or 32 KB (ATmega328) of which 2 KB is used by the boot loader.
- SRAM : 1 KB (ATmega168) or 2 KB (ATmega328).
- EEPROM : 512 bytes (ATmega168) or 1 KB (ATmega328).
- Clock Speed: 16 MHz.
- Dimensions : 0.73 x 1.70
- Length: 45 mm.
SKU: ARD-004 -
Arduino & IOT Boards, Shields
Arduino Porto PCB
The ProtoShield makes it easy for you to design custom circuits. You can easily solder TH or SMD ICs on the prototyping area to test them with your Arduino board. The SMD area is designed for a maximum of 24 pins SOIC integrated circuit and the TH area contains a lot of space for the needed components around your project. You can even stick a mini breadboard (not included) on the protoarea for solderless operation. The proto area includes also two power lines (IOREF and GND), two LEDs pads and SPI signals breakout pads for boards with SPI only on the ICSP header like Zero.
SKU: n/a
UNI-T UT33D+ Palm Size Digital Multimeter
8 MHz Crystal Oscillator
A2212 2200KV Brushless DC Motor BLDC
75W Ceramic Heater Heat Emitter Lamp Incubator
7905 Voltage Regulator
820K Ohm Resistor 1/4 Watt (5% tolerance)
A2212 1000KV Brushless DC Motor
A4988 Stepper driver
7812 Voltage Regulator
ARDUINO CNC SHIELD V3
7809 Voltage Regulator
Arduino Jumper Wire M/M 40Pcs
7818 Voltage Regulator
AMTECH RMA223 RMA-223 RMA559 Solder Paste Flux 10CC 






































