SUDER Soldering Iron 30W With Soldering Flux Soldering Wire Vectra 50g Soldering Foam Subtotal: ₨ 1,099
Shop
Showing 1153–1200 of 1337 results
-
Solder Paste, Soldering Accessories & Tools
Soldering Paste JYD 80 grams
This Soldering Paste is Environmentally Friendly and helps create higher quality solder joints. This 80g pack will last for a long time.
Specification :
- Non-poisonous
- Non-corrosive: safe for IC and PCB.
- Smoother welding surface.
- High joint quality
- Good insulation.
- Neutral PH : 7 0.3
SKU: n/a -
Soldering Accessories & Tools
Soldering Wick
Desoldering braid or desoldering wick is a pre-fluxed copper braid that is used to remove solder, which allows components to be replaced and excess solder (e.g. bridging) to be removed. The soldering iron is applied to the wick as it sits on the solder joint, and when both are brought up to the solder’s melting point, the flux is activated and, through capillary action from the braided design, solder is drawn up the wick.
SKU: n/a -
-
Relays & Interface Module, Solid State Relay (SSR)
Solid State Relay – 3A
Solid state relays have no moveable contacts. The primary advantage over a mechanical relay is that there are no switching contacts to physically wear out. PCB mount Solid State Relays are an excellent choice for high frequency switching applications in Factory Automation, I/O Modules or for control inputs from a position controller.
SKU: n/a -
Relays & Interface Module, Solid State Relay (SSR)
Solid State Relay – 4A MP240D4
Solid state relays have no moveable contacts. The primary advantage over a mechanical relay is that there are no switching contacts to physically wear out. PCB mount Solid State Relays are an excellent choice for high frequency switching applications in Factory Automation, I/O Modules or for control inputs from a position controller.
SKU: n/a -
-
Development Boards, STM32
ST Link V2 Programmer For STM8 & STM32 Microcontroller
- PCB installed inside of aluminium alloy U disk shell, portable, safe and reliable!
- The interface definition is directly marked on the shell, which is clear, convenient, and practical!
- 5V, and 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V
- Shell characters using laser engraving, never fade off! Permanent clarity!
- 500MA internal resettable fuse, complete protection of your expensive computer motherboard!
- The Red and blue LED indicator allows you to always observe ST-LINK V2 working conditions!
- With 4 DuPont lines, you can easily respond to different target board line orders!
- Use anti-static bag packaging.
SKU: n/a -
Arms/Grippers/Bipped, Robotics
Standard Gripper Kit B – Straight Mount
This is the Standard Gripper Kit B, a simple and durable robotics kit that is great for getting a grip on pretty much any robotics project! Designed for use with any standard size Hitec or Futaba servo, the gripper kit is easy to assemble and requires only a Phillips Head Screwdriver. This Standard Gripper is capable of opening an impressive 6″ wide max, has an overall body length of 5″ long with a 1.3″ wide servo housing body, and offers 6-32 mounting thru-holes along the edges of the servo housing.
SKU: n/a -
Incubator, Temperature & Humidity Controllers
STC-1000 Digital Temperature Controller Thermostat Module
Incubator, Temperature & Humidity ControllersSTC-1000 Digital Temperature Controller Thermostat Module
- Measuring range: -50 – 99°C.
- Resolution: 0.1°C.
- Accuracy: ±1°C (-50 – 70°C).
- Sensor error delay: 1 minute.
- Supply: 220VAC±10%, 50/60Hz
- Consumption: ≤3W.
- Sensor: NTC sensor (1PC).
- Relay contact capacity: Cool 10A/250VAC; Heat 10A/250VAC.
- Ambient temperature : 0 – 60°C.
- Storage temperature: -30 – 75°C.
- Relative humidity: 20% – 85% (No condensate).
- Front panel size : 75(L) x 34.5(W)(mm)
- Mounting size: 71(L) x 29(W)mm.
- Probe Length: 1m (include the probe).
- Size: 75(L) x 34.5(W) x 85(D)mm.
SKU: n/a -
Incubator, Temperature & Humidity Controllers
Stc3028 Digital Temperature And Humidity Controller
- Model: STC-3028
- Input Voltage: AC110 ~ 220V
- Measuring Temperature Range: -20 ~ 80
- Humidity Measurement Range: 00% RH ~ + 100% RH
- Accuracy: 1 , 0.1% RH
- Relay Output Contact Power: 10A / 240VAC
- Material: PC + ABS fireproof
- Panel size: 75x34mm / 2.95×1.34inch Installation
- size: 85x70x28mm / 3.35×2.76×1.10inch
- Cable length: 1m
SKU: n/a -
Motors & Drivers, Stepper Motor
Stepper Motor NEMA 17 Refurbish
- Stepper motor is known by its property to convert a train of input pulses into a precisely defined increment in the shaft position.
- This is a high-quality motor that can be used for a long time without stuck.
- It has a quite stable performance during work and will not lose step.
- Low noise and big torque, this is a great choice if you need a stepper motor.
- Stepper motor can be widely used for a 3D printer, CNC engraving machine, etc.
SKU: n/a -
-
Development Boards, STM32
STM Discovery Kit STM32F3 STM32F303VC
- STM32F303VCT6 microcontroller featuring 256 KB Flash, and 48 KB RAM in an LQFP100 package
- On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone ST-LINK/V2 (with SWD connector for programming and debugging)
- Board power supply: through USB bus or from an external 3 V or 5 V supply voltage
- External application power supply: 3 V and 5 V
- L3GD20, ST MEMs motion sensor, 3-axis digital output gyroscope
- LSM303DLHC, ST MEMs system-in-package featuring a 3D digital linear acceleration sensor and a 3D digital magnetic sensor
- Ten LEDs:
- LD1 (red) for 3.3 V power on
- LD2 (red/green) for USB communication
- Eight user LEDS, LD3/10 (red), LD4/9 (blue), LD5/8 (orange) and LD6/7 (green)
- Two pushbuttons (user and reset)
- USB USER with Mini-B connector
- Extension header for all LQFP100 I/Os for quick connection to prototyping board and easy probing
SKU: n/a -
Development Boards, STM32
STM32F103C8T6 Blue Pill STM32f103 Arm Cortex Dev Board
- 100% Brand new and high-quality STM32 Board
- 72MHz work frequency.
- 64K flash memory, 20K SRAM.
- 2.0-3.6V power, I/O.
- Reset(POR/PDR).
- 4-16MHz crystal.
- Onboard Mini USB interface, you can give the board power supply and USB communication.
SKU: n/a -
Development Boards, STM32
STM32F4 Discovery – Arm Cortex M4 Processor kit
- STM32F407VGT6 microcontroller featuring 32-bit ARM Cortex-M4F core, 1 MB Flash, 192 KB RAM in an LQFP100 package
- On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone ST-LINK/V2 (with SWD connector for programming and debugging)
- Board power supply: through USB bus or from an external 5 V supply voltage
- External application power supply: 3 V and 5 V
- LIS302DL or LIS3DSH ST MEMS 3-axis accelerometer
- MP45DT02, ST MEMS audio sensor, omni-directional digital microphone
- CS43L22, audio DAC with integrated class D speaker driver
- Eight LEDs:
- LD1 (red/green) for USB communication
- LD2 (red) for 3.3 V power on
- Four user LEDs, LD3 (orange), LD4 (green), LD5 (red) and LD6 (blue)
- 2 USB OTG LEDs LD7 (green) VBus and LD8 (red) over-current
- Two push buttons (user and reset)
- USB OTG FS with micro-AB connector
- Extension header for all LQFP100 I/Os for quick connection to prototyping board and easy probing
SKU: n/a -
Development Boards, STM32
STM32F401 F411 Black Pill Mini Development Board
- STM32F411CEU6 (100Mhz) with 512KB FLASH & 128KB RAM
- Onboard LDO for 5V to 3.3V DC conversion
- 2x 20 Pin Single Line Header which gives access to all the IOs. The board comes with unsoldered header connectors.
- The header for SWD Programming Interface
- Switches for Reset, Boot Mode, User
- LED for Power and another connected on GPIO(C13)
- 25MHZ high speed crystal, 32.768Khz low speed crystal
- BOOT0 and NRST, releasing NRST to access serial port download, and DFU download, using ST multi-in-one STM32 Cube Programmer burning software.
- Option to solder SPI Memory on the bottom side of the board.
- USB-C type Connector
SKU: n/a -
Batteries & Chargers
Super Heavy Duty 6F22 9V Camelion
- Frame size: 9V
- Dimensions (L x B x H mm): 26,2 x 17,2 x 48,3
- Weight (g): 36,4
- Electrochemical System: Zinc manganese dioxide/
- Zinc/ammonium chloride
- Nominal Capacity: 450mAh to 4,8V (20C-2 C rated capacity at 25mA continuous drain)
- Nominal Voltage: 9V
- Jacket: Metall
SKU: n/a -
Others, Sensors
SW-520D – Tilt Sensor Module
- Using high-sensitivity switch SW 520D as the sensor.
- The module is equipped with fixed bolt hole for convenient installation.
- Using LM393 wide voltage comparator, clean signal, good waveform, strong driving ability with output of more than 15 mA.
- The working voltage of 3.3V to 5V.
- Small PCB size:3.2cm x 1.4cm.
- Digital output form: digital switch output (0 and 1).
SKU: n/a -
Raspberry Pi
T-Cobbler Plus Kit – Breakout for Raspberry Pi
The T-Cobbler is add on prototyping board designed for 2×20 connecter typer RaspberryPi and can put all the GPIO and SPI pins onto a solderless board. The pins on the cobbler are labelled so clear that user doesn?t need the pin layout printout to work with the device
SKU: n/a -
Wires & Connectors
T-Plug T Connector Male/Female pair 50A
dean connector for quadcopter, tamiya connector, battery connector, deans connectors bulk, soldering deans, soldering rc battery connectors, how to change connectors on lipo battery,deans plugs rc, how to solder deans connectors to a lipo battery.
T connectors sold as matching male-female pairs and have a current rating of 50 A.
They are the smallest high-current connectors we know of, and they are great for projects that involve bigger motors and controllers. Often used to connect batteries in radio control models.
SKU: CON282 -
Desoldering Pump
Takumi Desoldering Pump (Long)
Providing safe, low-cost means of desoldering connections, PC boards, and components.
Large capacity spring-loaded plunger quickly removes solder in a single action.
Tool easily disassembles for fast cleaning, tip, and “O” ring replacement.
Plunger pin automatically purges solder from the tip with each use.
SKU: n/a -
Motor Drivers, Motors & Drivers
Tb6560 3a Stepper Motor Driver Module Cnc Single Axis Controller Module
Motor Drivers, Motors & DriversTb6560 3a Stepper Motor Driver Module Cnc Single Axis Controller Module
- Low cost and good high-speed torque
- Supply voltage up to +32 VDC
- Output current up to 3.0A
- Pulse frequency up to 20 KHz
- Suitable for 2-phase and 4-phase motors
- Over-voltage and short-circuit protection
- 7 output current choices, max 3200 steps/rev
- Automatic idle-current reduction
- Slim size (96x61x37mm)
SKU: n/a -
Motor Drivers, Motors & Drivers
TB6600 Arduino Stepper Motor Driver 4A, 5A
- This stepper motor driver supports 8 kinds of current control.
- This stepper driver supports 7 kinds of micro-steps adjustable.
- Stepper motor driver interface adopts high-speed optocoupler isolation.
- It has the feature of automatic semi-flow to reduce heat.
- It has a large area heat sink.
- It has anti-high-frequency interference ability.
- It has input anti-reverse protection
- It has the feature of overheating, over-current, and short circuit protection.
SKU: n/a -
Color, Mega Payday Sale, Sensors
TCRT5000 LFR Sensor
- Working voltage: DC 3.3V-5V
- Working current: 20mA
- Operating temperature: -10~+50
- detection distance :2-40cm
- IO Interface: 4-wire interfaces (-/+/S/EN)
- Output signal: TTL level (low level there is an obstacle, no obstacle high)
- Adjustment: adjust multi-turn resistance 8. Effective angle: 35.7.
- Size: 28mmx23mm
SKU: n/a -
-
Iron Stand, Soldering Accessories & Tools
TE-805 Helping Hand Soldering Stand.
- Max Magnification: 5X
- Material of Lens: Optical Glass Lens
- Materials of Frame: Metal
- Replace Lens: Yes
- With Light Or Not: No
- Style: Standing Style
- Material: Metal
- Diameter of Magnifier: 62mm
- Color: Silver + black
- Place of Application: Magnifier
SKU: n/a -
Peltier & accessories
TEC1 12715 136.8W 12V-15.4V 15A Peltier
Utilized in high-end consumer, commercial, and military-grade applications for extreme performance and maximum energy efficiency, TEC1 Peltier Modules provide unmatched temperature differentials (DTmax) in cooling or heating applications. TEC1-12715 Peltier Modules from electron.com measure 50x50x3.9mm and offer 68C Delta T max (DTmax) at a maximum operating temperature of 138C. Capable of performing to exacting specifications, cooling or heating with precision in extreme environments, TEC1 Peltier Modules from electron.com have rapidly become an industry standard for numerous exacting thermoelectrics.
SKU: n/a -
Development Boards, Other SBCs
Teensy 3.1
The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. The Teensy 3.1 brings a 32 bit ARM Cortex microprocessor into the mix so you can do some serious number crunching.
The Teensy 3.1 comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! You can program for the Teensy in your favorite program editor using C or you can install the Teensyduino add-on for the Arduino IDE and write Arduino sketches for Teensy!
The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32 bit processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access, several high-resolution ADCs and even an I2S digital audio interface! There are also 4 separate interval timers plus a delay timer! Oh yeah, and all pins have interrupt capability. Also, it can provide system voltage of 3.3V to other devices at up to 100mA.
SKU: n/a -
Communication Modules, RF Modules
Telemetry 3DR TTL
The Radio telemetry system base on 3DR Radio system and 100% compatible.
It’s designed as an open source Xbee replacement radio set, offering a lower price, longer range (approx one mile) and superior performance to Xbee radios. Its available in 915Mhz and 433Mhz; and in the following configurations: serial board (for the air) and USB (for the ground).
The system provides a full-duplex link using HopeRF’s HM-TRP modules running custom, open source firmware. Interface to the module is via standard 5V-tolerant TTL serial / FTDI USB serial.
Firmware upgrades and configuration are fully supported in the APM Mission Planner. Configuration is also possible through the 3DR Radio configurator and AT commands.
SKU: WRE186 -
-
Accessories, Clearance Sale
Telko S063 Portable Door Wedge Guard with Vibration and Contact Sensor New Os
Accessories, Clearance SaleTelko S063 Portable Door Wedge Guard with Vibration and Contact Sensor New Os
- High output: 120DB alarm siren
- Standard 9 volt battery operation
- Required no special installation
- Rugged high impact ABS construction
- Provide alarm siren operation from contact with door or from movement vibration.
SKU: n/a
